d escription ? 125 maximum total temperature operation ? surface mount inductors designed for higher speed switch mode applications requiring lower inductance and high current ? dual conductors allow for low inductance and high current or high inductance and lower current ? inductance range from .047uh to 0.480uh ? current range up to 42 amps ? meets ul 94v-0 flammability standard ? ferrite core material applications ? next generation microprocessors environmental data ? storage temperature range: -40 to +125? ? operating ambient temperature range: -40 to +125? (range is application specific). ? solder reflo w temper ature: +260 max. for 10 seconds max. packaging ? supplied in tape and reel packaging, 1700 (fp2-s and fp2-d) and 950 (fp2-s200 and fp2-vxxx) per reel p arallel mode p ar t inductance ocl (1) i rms (2) i sa t (3) dcr (4) height v olt- number h h amps amps sec (v s) (rated) 15% nom. ref . ( 5) single conductor fp2-s047-r 0.047 0.047 39.0 42.0 0.00024 3.00 0.75 fp2-s068-r 0.068 0.068 39.0 32.0 0.00024 3.00 0.75 fp2-s082-r 0.082 0.082 39.0 26.0 0.00024 3.00 0.75 fp2-s100-r 0.100 0.100 39.0 22.0 0.00024 3.00 0.75 fp2-s120-r 0.120 0.120 39.0 18.0 0.00024 3.00 0.75 fp2-s200-r 0.200 0.200 37.0 19.0 0.00028 5.00 0.99 fp2-v050-r 0.050 0.050 37.0 70.0 0.00028 5.00 0.99 fp2-v100-r 0.100 0.100 37.0 40.0 0.00028 5.00 0.99 FP2-V120-R 0.120 0.120 37.0 33.0 0.00028 5.00 0.99 fp2-v150-r 0.150 0.150 37.0 25.5 0.00028 5.00 0.99 double conductor fp2-d047-r 0.047 0.047 37.0 42.0 0.00026 3.00 0.75 fp2-d068-r 0.068 0.068 37.0 32.0 0.00026 3.00 0.75 fp2-d082-r 0.082 0.082 37.0 26.0 0.00026 3.00 0.75 fp2-d100-r 0.100 0.100 37.0 22.0 0.00026 3.00 0.75 fp2-d120-r 0.120 0.120 37.0 18.0 0.00026 3.00 0.75 series mode part inductance ocl (1) i rms (2) i sat (3) dcr (4) height volt- (5) number ? ref. ? amps amps sec (v?) (rated) ref. ref. ref. doub le conductor fp2-d047-r 0.188 0.188 16.0 21.0 0.0013 3.00 1.50 fp2-d068-r 0.272 0.272 16.0 16.0 0.0013 3.00 1.50 fp2-d082-r 0.328 0.328 16.0 13.0 0.0013 3.00 1.50 fp2-d100-r 0.400 0.400 16.0 11.0 0.0013 3.00 1.50 fp2-d120-r 0.480 0.480 16.0 9.0 0.0013 3.00 1.50 notes: (1) open circuit inductance t est p arameters: 1mhz, .100vrms, 0.0adc. (2) rms current f or an appro ximate ? t of 40 c without core loss. it is recommended that the temperature of the part not exceed 125. (3) p eak current f or appro ximately 30% rolloff at 20. (4) dcr limits 20 c . (5) applied v olt-time product (v - s) across the inductor . this value represents the applied v-? at 500khz necessary to generate a core loss equal to 10% of the total losses f or 40 c temper ature rise. flat-pac? low profile inductors (surface mount) rohs 2 002/95/ec
mechanical diagrams single conductor notes: (1) mar king sxxx = s: single conductor style , dxxx = d: dual conductor style , xxx - last three digits of par t n umber . date code: yww = y: last digit of year, ww: week of year. (2) all dimensions are in millimeters unless otherwise specified. (3) f or par allel mode oper ation, connect ter minals 1 to 4 and 2 to 3 on pcb (use single conductor pcb la y out) f or ser ies mode oper ation, connect ter minals 2 to 4 on pcb (dual conductor model). 6 .70 max 7.20 max ( s or v)xxx yww top view 2 1 2.50 (2x) 7.50 6.50 (4x) 1 2 pcb pad layout 2 1 s chematic 3.0 ref. height mm max 1.30 ref. (2x) front view side view 1.0 min. (2x) dual conductor 6 .70 max yww 7.20 max dxxx top view 2 1 3 4 pcb pad layout 2.50 (2x) 7.50 3.00 ( 4x) 0.50 2 winding mode 2.50 (2x) 7.50 3.00 ( 4x) 0.50 (typ) series mode 4.50 (2x) 1.50 1 4 2 3 1 4 2 3 3.00 mm max 1.30 ref. (2x) front view 1.25 (2x) ref. 1 .00 ref. schematic winding 1 2 1 winding 2 3 4 side view (4x) packaging information ko 1.5 dia
min. bo ao 12.0 4.0 2.0 1.5 dia.
+0.1/-0.0 a a 1.75 7.5 16.0
+/-0.3 1 2 ao=6.6mm bo=7.1mm ko=3.2mm ko=5.2mm (fp2-s200 & fp2v) a ctu al size flat-pac flat-pac? low profile inductors (surface mount) direction of f eed
inductance characteristics flat-pac? low profile inductors (surface mount) core loss i rms der ating with core loss 1000 800 6 00 500 400 300 2 00 1 00 80 60 50 40 30 20 10 % of applied v olt- -seconds 99 98 97 96 95 94 92 90 80 70 60 50 40 20 0 % o f l o s s e s f r o m i r m s ( m a x i m u m ) 1 m h z 5 0 0 k h z 3 0 0 k h z 2 0 0 k h z 1 0 0 k h z inductance characteristics core loss i rms der ating with core loss 1000 800 6 00 500 400 300 2 00 1 00 80 60 50 40 30 20 10 % of applied v olt- -seconds 99 98 97 96 95 94 92 90 80 70 60 50 40 20 0 % o f l o s s e s f r o m i r m s ( m a x i m u m ) 1 m h z 5 0 0 k h z 3 0 0 k h z 2 0 0 k h z 1 0 0 k h z
flat-pac? low profile inductors (surface mount) visit us on the web at www.cooperbussmann.com 1225 brok en sound pkwy. suite f boca raton, fl 33487 tel: +1-561-998-4100 toll free: +1-888-414-2645 fax: +1-561-241-6640 this bulletin is intended to present product design solutions and technical information that will help the end user with design applications. cooper electronic t echnologies reser ves the right, without notice, to change design or construction of any products and to discontinue or limit distribution of any products. cooper electronic t echnologies also reser ves the right to change or update, without notice, any technical information contained in this bulletin. once a product has been selected, it should be tested by the user in all possible applications. life support policy: cooper electronic technologies does not authorize the use of any of its products for use in life support devices or systems without the express written approval of an officer of the company. life support systems are devices which support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. pm-4110 3/07 cooper electronic technologies 2007
|
